10×10 Lean to Shed Doors Plans
This step by step diy project is about 10×10 shed doors plans. This is PART 3 of the outdoor lean to shed project, where I show you everything you want to know about framing the door and fitting the trims. Take a look over the rest of my woodworking plans, if you want to get more building inspiration. Remember that you need to select the site for the shed with attention and that you have to comply with a few legal regulations.
When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day.
Projects made from these plans
10×10 Lean to Shed Door Plans
Building a 10×10 lean to shed
- M – 2 pieces of 2×4 lumber – 80″ long, 1 piece – 79″ long JAMBS
- N – 2 pieces of 2×4 lumber – 73″ long, 1 piece – 36″ long, 1 piece – 29″ long, 1 piece of T1-11 s >2xDOOR
- O – 4 pieces of 1×4 lumber – 116″ long, 2 pieces – 90 1/2″long, 2 pieces – 89 3/4″ long TRIMS
- 10 pieces of 2×4 lumber – 8′
- 4 pieces of 1×4 lumber – 8′
- 4 pieces of 1×4 lumber – 10′
- 2 pieces of T1-11 siding – 4’x8′
- front door hinges
- 8d nails, 2 1/2″ screws, 3 1/2″ screws,1 5/8″ screws
- wood filler , wood glue, stain/paint
- shed accessories
- PART 1: 10×10 Shed Plans
- PART 2: 10×10 Shed Plans Roof Plans
- PART 3: 10×10 Shed Door Plans
How to build a 10×10 shed door and trims
Fitting the jambs
The first step of the project is to attach the 2×4 jambs around the front door opening. Fit the 2×4 jambs around the door opening. Align the edges flush and insert 2 1/2″ screws to secure them into place tightly.
Building the doors
Use T1-11 siding for the door panels and 2×4 lumber for the trims. First, you have to build the door frame. Drill pocket holes and insert 2 1/2″ screws to lock the frames together tightly. Make sure the corners are square and align the edges flush. Fit the panel to the frame and insert 2″ brad nails to lock them together tightly.
Fitting the double doors
Fit the doors to the opening and then secure it to the jambs with hinges. Install a latch so you can lock the door into place tightly. Install handles so you can open and close the door easily.
Side wall trims
Fit the 1×4 trims to the sides of the shed. Use a miter saw to make the angle cuts and then secure the trims into place with 2″ nails, every 8″ along the framing.
Back wall trims
Fit the 1×4 trims to the back of the shed. Align the edges flush and insert 2″ nails to secure them into place tightly.
Front wall trims
Fit the decorative trims to the front of the shed. Make the cuts to the trims and then secure them into place with 2″ nails.
10×10 Lean to shed – Free DIY Plans
Last but not least, take care of the finishing touches. Fill the holes with wood putty and smooth the surface with 120-220 grit sandpaper. Apply a few coats with paint or stain to enhance the look of the shed and to protect the components from decay. Check out PART 1 for the frame plans and PART 2 for the roof plans.
This woodworking project was about 10×10 shed door plans free. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.