Home built bandsaw mill
by Rick Allen at gardenofwar.gq.nu
Band saw lumber mill design notes. This is not a how to. It’s just some photos of a mill I built and use. If you attempt this you are on your own. I can take no responsibility for your injuries (which you will sustain on use). There are many things that can go wrong with this and either kill you, maim you or people nearby. Blades break, engines can explode or catch fire, motors can short and electrocute you. I once had a blade break and had an 8 inch section sticking out of the shed you can see in some of the photos. (build a blade guard) But it can be built and used to good effect if you are real careful. Custom blades can be purchased in most cities – look in your yellow pages. No plans are included as there can be none with a junkyard sawmill – it’s a case of find it and weld it on. Read and use at your own considerable risk.
(Click here to view full size image)
The comments below were added after this article was archived in the Knowledge Base (add your comment).
Comment from contributor A:
I had a machine shop build a bandmill of my own design, similar to this. The following comments explain what I wish I had done.
1. Factory made steel bandmill wheels would not have cost any more. Machining of auto wheels to run true was expensive. Also, machining the proper radius on the tire was a problem.
2. Rails and log bunks should be at least 1/2″. Costs only a few dollars more. You will never get a good cut unless the tracks are straight and true. I use 16 leveling bolts to keep my frame true.
3. Four post, not just two.
4. Better to buy Suffolk saw guides than make your own.
5. Drive arbor should be at least 1.5″ if extended over 5 inches.
6. *Raise the bed frame* at least 18 inches high. You may want to add hydraulic dogging and log turning at some point.
7. Some form of hydraulics to raise and lower the saw head. I use a worm gear winch and it is a real pain and very slow.
8. Bolt everything together *first*. After it is “true”, then weld. Even the major firms are now doing it this way.
9. If you are cutting over 14″ wide, it might be best to use a 20 HP gas motor or an electric 10 HP industrial motor.
10. For your posts, pick up used hydraulic cylinders (they get thrown away). A little design rework and mounting in square tube frame sections will do wonders for your saw.
I should mention that I am not unhappy with my saw, as I can cut 1/6″ veneer 12′ wide by 18′ long. I cut mesquite, a very hard wood and this type of saw does quite well.
Should you follow the ideas above, you will find yourself with a $20,000 saw for less than $5,000.
Comment from contributor B:
I too just finished a mill (William Rake’s plan) similar to the one in this article. Concerning the choice of winch, the advantage of a worm gear winch is precise adjustment. The advantage of a regular boat winch is speed of movement. A compromise that I think works well is a standard boat winch that has a braking mechanism and a 1 1/2 to 2 inch drum. I can raise or lower the the head quickly without engaging or disengaging a lock and two times out of three the “clicker” will hit my desired level. When the last click is too high I just back off about an 1/8 inch and reset.
Have you reviewed the related Knowledge Base areas below?
Would you like to add information to this article? . Click Here
If you have a question regarding a Knowledge Base article, your best chance at uncovering an answer is to search the entire Knowledge Base for related articles or to post your question at the appropriate WOODWEB Forum. Before posting your message, be sure to review our Forum Guidelines.
Questions entered in the Knowledge Base Article comment form will not generate responses! A list of WOODWEB Forums can be found at WOODWEB’s Site Map.
When you post your question at the Forum, be sure to include references to the Knowledge Base article that inspired your question. The more information you provide with your question, the better your chances are of receiving responses.
Letters, questions or comments? E-Mail us and let us know what you think. Be sure to review our Frequently Asked Questions page.
Contact us to discuss advertising or to report problems with this site.
Copyright © 1996-2019 – WOODWEB ® Inc.
All rights reserved. No part of this publication may be reproduced in any manner without permission of the Editor.
Review WOODWEB’s Copyright Policy.
The editors, writers, and staff at WOODWEB try to promote safe practices. What is safe for one woodworker under certain conditions may not be safe for others in different circumstances. Readers should undertake the use of materials and methods discussed at WOODWEB after considerate evaluation, and at their own risk.
335 Bedell Road
Montrose, PA 18801