8×14 Gable Shed Roof – Free DIY Plans
This step by step woodworking project is about 8×14 gable shed roof plans. This is the PART 2 of the 8×14 garden shed project, where I show you how to build the gable roof for the shed. Building the roof for the shed is really easy if you follow my tips and diagrams with attention. Read the local codes before starting the project, so you comply with the requirements. See my other DIY projects HERE.
We recommend you to invest in the best materials you could afford. Therefore, you should buy weather-resistant lumber, such as pine or cedar. Always take accurate measurements before adjusting the size of the components at the proper size. Drill pilot holes trough the components before inserting the wood screws, to prevent the wood from splitting.
Made from this plan
8×14 Gable Shed Roof Plans
Building a 8×14 shed
- G – 4 pieces of T1-11 s >SIDING
- H – 2 pieces of 2×4 lumber – 60″ long, 1 piece – 88 3/4″ long 8xTRUSS
- I – 4 pieces of 2×4 lumber – 60″ long, 10 pieces – 6 1/2″ long 2xOVERHANG
- J – 2 pieces of 3/4″ plywood – 48″x96″ long, 2 pieces – 48″x72″ long, 4 pieces – 10″x60″ long, 4 pieces – 12″x48″ long, 2 pieces – 12″x72″ long ROOF
- K – 4 pieces of 2×6 lumber – 61″ long, 2 pieces of 1×6 lumber – 188″ long TRIMS
- L – 150 sq ft of tar paper, 150 sq ft of asphalt shingles ROOFING
- 1 piece of T1-11 siding – 4’x8′
- 8 pieces of 2×4 lumber – 10′
- 8 pieces of 2×4 lumber – 8′
- 6 pieces of 3/4″ plywood – 4’x8′
- 4 pieces of 2×6 lumber – 6′
- 2 pieces of 1×6 lumber – 16′
- 150 sq ft of tar paper, 150 sq ft of asphalt shingles
- 2 1/2″ screws, 3 1/2″ screws, 1 5/8″ screws
- 4d nails, 6d nails
- rafter ties
- wood filler , wood glue, stain/paint
5×5 Gable Shed Roof – DIY Plans
Building the rafters
Use 2×4 lumber for the rafters. Mark the cut lines on the beams and then get the job done with a circular saw. Smooth the edges with sandpaper.
Assembling the trusses
Use 2×4 lumber for the bottom rafters. Use a miter saw to make the angle cuts at both ends of the bottom rafters and then lay all the components on a level surface.
Fitting the gussets
Use 1/2″ plywood for the gussets. Use a circular saw to make the cuts, as shown in the diagram. Add the gussets to the rafters and lock them into place with 1 5/8″ screws.
Fitting the trusses
Fit the rafters to the top of the shed. Place the rafters every 24″ on center, equally spaced, as shown in the diagram. Drill pilot holes and insert 3 1/2″ screws to lock the rafters into place tightly. Alternatively, you can use rafter ties to lock the trusses to the plates.
Gable end panels
Use T1-11 siding sheets for the gable ends. Mark the cut lines on the sheets and then get the job done with a saw. Align the edges with attention and insert 6-8d nails, every 8″ along the framing.
Building the overhangs
Use 2×4 lumber for the overhangs. You can adjust the size of the overhangs according to the size of the blockings.
Fitting the gable ends
Fit the overhangs to the front and back of the shed. Align the edges with attention, drill pilot holes and insert 3 1/2″ screws.
Fit 3/4″ plywood sheets to the roof of the shed. Align the sheets with attention, making sure you leave no gaps between them. Insert 1 5/8″ screws to lock the sheets into place, every 8″ along the rafters.
Front and back roof trims
Use 1×6 lumber for the front and back roof trims. Cut the trims as shown in the diagram. Attach the trims to the gable ends and then lock them into place with 2 1/2″ screws.
Fit 1×6 trims to the sides of the roof. Align the edges with attention and then insert 2″ nails to lock them into place tightly.
Fitting the roofing
Cover the roofing sheets with tar paper. Install the tar paper starting with the bottom of the roof and make sure the strips overlap for at least 2″. In addition, fit a 12” strip over the top ridge. Install the shingles starting with the left- bottom of the roof, after fitting the starting course. Use roofing tacks to secure the shingles into place.
This shed is ideal if you need storage space but you have a narrow backyard. Make sure you take a look over PART 1 and PART 3 of the project, so you learn how to build the frame and how to build the front door.
Thank you for reading our project about free 8×14 gable shed roof plans and I recommend you to check out the rest of the projects. Don’t forget to LIKE and SHARE our projects with your friends, by using the social media widgets. SUBSCRIBE to be the first that gets our latest projects.