Naturally , before you start creating the lose, you must have 8×12 Run in Shed Roof Plans, MyOutdoorPlans, Free Woodworking Plans and Projects, DIY Shed, Wooden Playhouse, Pergola, Bbq. It makes the construction easier and permits us to easily determine the number of developing materials you will need with your 8×12 Run in Shed Roof Plans, MyOutdoorPlans, Free Woodworking Plans and Projects, DIY Shed, Wooden Playhouse, Pergola, Bbq.

8×12 Run in Shed Roof Plans, MyOutdoorPlans, Free Woodworking Plans and Projects, DIY Shed, Wooden Playhouse, Pergola, Bbq

horse shed woodworking plans

8×12 Run in Shed Roof Plans

This step by step diy woodworking project is about 8×12 run in horse shelter roof plans. This article is PART 2 of the small run in shed project, where I show you how to frame the lean to roof and how to fit the decorative trims. Make sure you check out the rest of plans to see alternatives and more projects for your garden.

When buying the lumber, you should select the planks with great care, making sure they are straight and without any visible flaws (cracks, knots, twists, decay). Investing in cedar or other weather resistant lumber is a good idea, as it will pay off on the long run. Use a spirit level to plumb and align the components, before inserting the galvanized screws, otherwise the project won’t have a symmetrical look. If you have all the materials and tools required for the project, you could get the job done in about a day.

Projects made from these plans

8×12 Run in Shed Roof Plans

  • E – 3 pieces of T1-11 s >SIDING
  • F – 10 pieces of 2×6 lumber – 117″ long RAFTERS
  • G – 2 pieces of 3/4″ plywood – 48″x96″ long, 1 piece – 21″x96″ long ROOF SHEETS
  • G – 130 sq ft of tar paper, 130 sq ft of asphalt shingles ROOFING
  • H – 2 pieces of 2×8 lumber – 117″ long, 2 pieces of 1×8 lumber – 148 1/4″ long TRIMS
  • 10 pieces of 2×6 lumber – 10′
  • 2 pieces of 1×8 lumber – 14′
  • 2 pieces of 2×8 lumber – 10′
  • 3 pieces of 3/4″ plywood – 4’x8′
  • 4 pieces of T1-11 siding – 4×10′
  • 4 pieces of T1-11 siding – 4’x8′
  • 130 sq ft of tar paper
  • 130 sq ft of asphalt shingles
  • 2 1/2″ screws, 3 1/2″ screws, 1 5/8″ screws

Hammer, Tape measure, Framing square, Level

Miter saw, Drill machinery, Screwdriver, Sander

Safety Gloves, Safety Glasses

One weekend

Building a 8×12 shed roof plans

Back wall siding panels

The first step of the project is to attach the 5/8″ T1-11 siding sheets to the back of the run in shed. Therefore, cut the sheets at the dimensions shown in the diagram and then align them into place. Leave no gaps between the sheets and insert 6-8 d nails to lock them into place tightly.

Front wall sheets

Cut the and attach the siding panels to the front of the shed. Insert the nails every 8″ along the framing.

Rafters for shed

Build the rafters from 2×6 lumber. Make a notch to the rafters, using the information from the diagram. Smooth the recess with a damp cloth.

Fitting the rafters to the 8×12 shed

Fit the rafters to the top of the shelter. Drill pilot holes and lock the rafters to the structure with screws and rafter ties. Place the rafters every 16″ on center.

Side siding panels

Continue the project by fitting the panels to the sides of the shed. Make the cuts so you can fit the panels into place tightly. Insert 6-8 d nails, every 8″ along the framing.

Attach 3/4″ plywood sheets to the rafters, using the pattern shown in the diagram. Drill pilot holes and insert 1 5/8″ screws, every 8″ along the rafters.

Fitting the roof trims

Fit the 2×8 trims to the sides of the roof. Align the edges with attention, drill pilot holes and insert 3 1/2″ screws to lock them into place tightly. Fit the 1×8 trims to the front and to the back of the shed. Cut the components at the right dimensions and then align them into place with attention. Drill pilot holes and then insert 3 1/2″ screws.

Fitting the roofing

Cover the roof of the shed with roofing felt, making sure the strips overlap at least 2″. Secure the tar paper to the plywood sheets with roofing staples. Fit the side drip edges over the roofing felt, while the bottom drip edges should be fit under.

8×12 run in shed plans

The run in shelter is sturdy and easy to build. This shed has an easy access on the front wall.

8×12 run in shed plans – front view

Fill the holes with wood putty and let them dry out for a few hours. Smooth the surface with 100-200 grit sandpaper and remove the residues with a damp cloth.

Top Tip: Check out PART 1 of the project, to learn how to build the frame for the 8×12 run in shed.

This woodworking project was about 8×12 run in horse shelter plans. If you want to see more outdoor plans, check out the rest of our step by step projects and follow the instructions to obtain a professional result.

Leave a Reply

Your email address will not be published. Required fields are marked *